High Output 4 Stage Turbine 7.5 PSI
	20' of 3/4' Tiger flex Spray Hose
	4' Whip Hose
	Pro Series BOTTOM FEED LEX-AIR Spray Gun (TOP FEED $75.00 MORE CALL)
	1.1 mm Needle Nozzle
	Quick Disconnect
	Air Control Valve
	"How to Spray" Instruction Guide
	Instruction Manual
	incoming Air filter system
	3M Accuspray gun $100.00 MORE TOP FEED $75.00

This system, the Axis SP2004, is quality-built with a high output four stage turbine which provides the power you need to atomize high viscosity materials, 7.5 PSI at the gun. It comes standard with a professional series HVLP spray gun designed to give automotive finish quality results. It will provide you with the extra atomization necessary for the finest finish. Designed for all stages of finish work on autos, airplanes and marine, fine woodworking, and modeling. This system is versatile and powerful enough to use for practically any painting task. Polyurethane, Epoxy, Waterborne, Multi-Color, Fillers, and Gel Coats, Clear Coats, Algrip.The 4 stage has all the features as the 3 stage above only with a more powerful motor.

No compressor is needed to operate the system, which eliminates the oil and moisture problem so prevalent with other kinds of sprayers. Another advantage is that the system is totally portable, lightweight and uses standard household electricity. A natural by-product of any turbine system is the addition of heat to the airline. The advantage of the heat is that it eliminates moisture from the air that is mixed with the paint, however, the disadvantage of this heat is that it has a tendency to also flash away some of the thinner that is added to the paint when it is mixed. This loss of thinner can render the paint droplets too dry when they are applied causing an 'orange peel' effect. The solution is to add more thinner to the paint when it is mixed to compensate for its span style="font-family: Arial">loss. The turbine raises the temp of the air 20 degrees above the air, which must be taken into consideration in high room temperature (the motor should be run for a few minutes to let the air temperature adjust to a steady degree). Another way to help to control the heat is to add a short piece of natural rubber 'stub hose' at the pump outlet. We call it an 'HD' or heat dissipation hose and is included in every AXIS spray system.

The way to get a great finish when spraying is to have a system that will break up the paint droplets as small as possible when it is atomized, the smaller the droplets, the better the finish.  Because this atomization (mixing the paint with the air) takes place as the paint exits the nozzle and mixes with the air it stands to reason that the smaller the nozzle hole is, the smaller the droplets are broken down.

  The big advantage to HVLP is that it saves you at least 50% of your paint with 90% of the paint going to the surface and STAYING thus eliminating the over spray and allowing you to actually see what you are painting.

  The Axis Paint sprayer is a true HVLP Sprayer with 110 CFM but only 5.5PSI The kit comes with a three-stage turbine, 40 ft. of hose and a 4ft flexible hose at the gun for easier movement and the gun.

The gun is a “LEX-AIR” There is a material flow adjustment knob at the rear of the gun and the pattern control at the front will allow you to adjust the pattern from a small circle (which will save your paint on small jobs) to a 12 inch fan either vertical or horizontal With just a little practice, adjusting the gun for the right flow and fan, a high quality job can be achieved. We also have many accessories and additional Products to help you get the job done right the first time.

  With other options the web site http://clmcenterprises.com has a lot more information or if you have questions not covered please call me toll free at 877-949-5183 or Email clmcarcare1@gmail.com

                                                                                                                                                        Our units are Proudly Manufactured in the USA in Gilberts Il.

ALL ITEMS ARE IN STOCK. ALL ORDERS PLACED BY 1PM CST WILL BE SHIPPED SAME DAY

*US funds $ dollars Prices subject to change without notice.  no guarantee on pricing in case of misprints

BACK TO TOP    Back to Main menu 

 AXIS Products Inc. Does not manufacture any system components that go into the finished system.  All components, such as the turbine and the spray gun are made by companies  who specialize in  making just the turbines or just the spray guns. This allows us to choose the best products  available on the market and combine them into one very high quality spray system.

Our competitors, who make all their own components, usually have one weak area in their design              that lessens the quality of their entire system. They may offer a quality turbine but include a spray gun that gives inconsistent results or design a very good spray gun without providing a turbine strong enough to power it.

 

suggestions & tips for good paint job        

CLM Enterprises offers other products, please e-mail us for a complete listing of our products.
MANY MORE PRODUCTS ARE AVAILABLE IN DEFERENT SIZES AND USES

Contact Information

Telephone

815 468 0139

 

Postal address

555 Rock Creek Dr.

             Manyeno,IL.60950

Electronic mail

Customer Support: sales@clmcenterprises.com
Webmaster: TeamZen Web Services

CLM. Enterprises is an authorized distributor for Axis Corp and the 3M Corp.

Fast Counter by Link Exchange